Crown X3000 Stereo 2x750W Power Amp  

Product #H88827

45 day price guarantee, 45 day return policy, 100% secure shopping

Unavailable

Item Note:

This product has been discontinued but may be available as a Open Box item.

Similar Items

See All Crown Live Power Amplifiers
Crown

Crown power without paying a princely sum.

The X Series of power amplifiers from Crown represents a new era in affordable, quality power amplification. All four models in the series are powerful, rugged and reliable. They are suited for musicians, DJs, and entertainers as well as houses of worship, discos, and pubs. Features include RCA and XLR inputs, user selectable input sensitivity of 0.755V or 1.4V, Speakon and binding post outputs, stereo/parallel/bridge-mono mode, power/fault/signal presence/clip indicators, forced-air cooling; and protection against shorts, no-load, on/off thumps and radio-frequency interference. The Crown X3000 has an output of 750W per side at 4 ohms.

With more than six decades of experience designing and building rock-solid products, Crown is the standard in amplifier technology. Check out the affordable Crown X Series.

Features
  • Stereo/parallel/bridge-mono mode
  • User selectable input sensitivity - 0.775V and 1.4V
  • Electronically balanced RCA & XLR inputs; binding post and Speakon outputs
  • Efficient forced-air cooling prevents excessive thermal buildup
  • Electronically balanced RCA & XLR inputs; binding post and Speakon outputs
  • Two level controls, power switch, power LED, and six LEDs which indicate signal presence, clip and fault for each channel
  • Protection against shorts, no-load, on/off thumps and radio-frequency interference

Go power mad. Order today.

 

X3000 Stereo 2x750W Power Amp Specifications:

  • Guaranteed Minimum Power: 750W (per channel) @ 4 ohms / 500W (per channel) @ 8 ohms / 1500W bridge mono @ 8 ohms
    Frequency Response (at 1 Watt): 20Hz - 20kHz, +0/-1dB
    Total Harmonic Distortion (THD): < 0.5%, 20 Hz - 20 kHz
    Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output
    to “30 dB: 0.35%
    Slew Rate: >10V/us
    Voltage Gain: 29dB 31dB 33dB 36dB
    Damping Factor (8 ), 10 Hz - 400 Hz > 200
    Signal-to-Noise Ratio: (below rated power,
    20 Hz to 20 kHz, A-weighted): > 100 dB
    Crosstalk (below rated power)
    At 1 kHz: “75 dB
    At 20 kHz: “59 dB
    Input Sensitivity for full rated power at 8  0.775V or 1.4V
    Input Impedance (nominal)
    Balanced: 20 k
    Unbalanced: 10 k

    Connectors, Controls and Indicators
    Input Connectors: One balanced XLR and one unbalanced RCA per channel
    Output Connectors: (Speaker Connectors) 4-POLE Speakon and one pair Binding Post per channel
    Front Panel Controls: Power on/off switch, one gain control per channel
    Rear Panel Controls Output mode switch: stereo (dual), parallel or bridge
    Input sensitivity switch: 0.775V or 1.4V
    Power Indicator: One blue LED
    Signal Indicator: One green LED per channel
    Clip (peak) Indicator: One yellow LED per channel
    Fault Indicator: One red LED per channel

    Construction
    Protection: Protection against short circuits, no-load, on/off muting,
    RF interference. Stable into reactive or mismatched loads
    Ventilation: Flow-through ventilation from front to back
    Cooling: Internal heat sinks with forced air. Fan cooled,
    speed regulated, thermal protection
review resources
Loading....