Crown X2000 Stereo 2x450W Power Amp  

Product #H88828

45 day price guarantee, 45 day return policy, 100% secure shopping


Item Note:

This product has been discontinued but may be available as a Open Box item.

Similar Items

See All Crown Live Power Amplifiers

Crown power that won't cost the temple jewels.

The X Series of power amplifiers from Crown represents a new era in affordable, quality power amplification. All four models in the series are powerful, rugged and reliable. They are suited for musicians, DJs, and entertainers as well as houses of worship, discos, and pubs. Features include RCA and XLR inputs, user selectable input sensitivity of 0.755V or 1.4V, Speakon and binding post outputs, stereo/parallel/bridge-mono mode, power/fault/signal presence/clip indicators, forced-air cooling; and protection against shorts, no-load, on/off thumps and radio-frequency interference. The Crown X2000 has an output of 450W per side at 4 ohms.

With more than six decades of experience designing and building rock-solid products, Crown is the standard in amplifier technology. Check out the affordable Crown X Series.

  • Stereo/parallel/bridge-mono mode
  • User selectable input sensitivity - 0.775V and 1.4V
  • Electronically balanced RCA and XLR inputs; binding post and Speakon outputs
  • Efficient forced-air cooling prevents excessive thermal buildup
  • Electronically balanced RCA and XLR inputs; binding post and Speakon outputs
  • Two level controls, power switch, power LED, and six LEDs which indicate signal presence, clip and fault for each channel
  • Protection against shorts, no-load, on/off thumps and radio-frequency interference

Beef up your system. Order today.


X2000 Stereo 2x450W Power Amp Specifications:

  • Guaranteed Minimum Power: 450W (per channel) @ 4 ohms / 330W (per channel) @ 8 ohms / 900W bridge mono @ 8 ohms
    Frequency Response (at 1 watt): 20Hz - 20kHz, +0/-1dB
    Total Harmonic Distortion (THD): < 0.5%, 20Hz - 20kHz
    Intermodulation Distortion (IMD) 60Hz and 7kHz at 4:1, from full rated output
    to “30 dB: 0.35%
    Slew Rate: >10V/us
    Voltage Gain: 29dB 31dB 33dB 36dB
    Damping Factor (8), 10Hz - 400Hz > 200
    Signal-to-Noise Ratio: (below rated power, 20Hz to 20kHz, A-weighted): > 100dB
    Crosstalk (below rated power)
    At 1kHz: “75dB
    At 20kHz: “59dB
    Input Sensitivity for full rated power at 8Ohm: 0.775V or 1.4V
    Input Impedance (nominal)
    Balanced: 20K
    Unbalanced: 10K
    Connectors, Controls and Indicators
    Input Connectors: One balanced XLR and one unbalanced RCA per channel
    Output Connectors: (Speaker Connectors) 4-POLE Speakon® and one pair Binding Post per channel
    Front Panel Controls: Power on/off switch, one gain control per channel
    Rear Panel Controls Output mode switch: stereo (dual), parallel or bridge
    Input sensitivity switch: 0.775V or 1.4V
    Power Indicator: One blue LED
    Signal Indicator: One green LED per channel
    Clip (peak) Indicator: One yellow LED per channel
    Fault Indicator: One red LED per channel
    Protection: Protection against short circuits, no-load, on/off muting,
    RF interference. Stable into reactive or mismatched loads
    Ventilation: Flow-through ventilation from front to back
    Cooling: Internal heat sinks with forced air. Fan cooled,
    speed regulated, thermal protection
review resources
write a review
Also consider